Contact-Systems and Accessories for Anodising and Electroplating Equipment 2000

High Current Contacts and Accessories for Rack Systems Contact Saddles - Standard 250 - 3000 A Contact Saddles - Two Piece Model 4000 - 14000 A Contact Saddles - with Integrated Guides 250 - 4000 A High Current Bolt Contacts 1000 - 12000 A Pneumatic Contacts with Moveable Contact Fingers 4000 - 20000 A Work Rods, Bimetallic Sheets and Washers Anodes and Small Contact Saddles 250 - 2500 A Contact Saddles with Spring and Stamped Contact Plates 1500 - 3000 A Bar supports - Metal and Plástic Contacts for Galvanising Racks Rack Contacts Rack Contact Holders Cam Levered Rack Contacts Wing Screws and...

Factory View Neuenkamper Strasse Factory View Lenneper Strasse Aerial photograph of our factory P. Druseidt Elektrotechnische Spezialfabrik GmbH & Co. KG Neuenkamper Strasse 105 · 42855 Remscheid · Germany P.O. Box 10 02 25 · 42802 Remscheid · Germany Phone +49 (21 91) 93 52-0 · Fax +49 (21 91) 93 52-150 E-Mail: [email protected] · Internet: www.druseidt.de

Quality and constructive know-how backed by modern production technology ... Construction + Production + Quality Assurance = Quality Products ... provide the user with a wide range of contacts and current transfer elements, fine tuned to the respective requirements. 42855 Remscheid, Neuenkamper Str. 105 Telefon + 49 (21 91) 93 52 - 0 Telefax + 49 (21 91) 93 52 - 150 E-Mail: [email protected] 3/2

High Current Contacts for Galvanising Equipment Much emphasis is being placed on the quality of finishing and plating galvanising and electroplating. These increasing requirements are simultaneously combined with the demands for inexpensive methods and rational, low-maintenance production procedures. Every component of a plating system must therefore be equipped to meet these prerequisites. Weak points which can be the cause for repairs or system down-time or that could lead to plating problems must be avoided or eliminated. A major prerequisite for optimal processing is that the current required...

High Current Contactors for Work Rod Systems High Current –Contact Saddles 250 - 3000 A One Piece Standard Version A proven druseidt contact system for decades. Technically up-to-date and continuously under development. Supplied either as one piece standard contact for a bus-bar thickness of 10/15 or 20 mm or as a ready-to-install contact unit complete with base, i.e., integrated power connection bar or angle and insulation plate. Contacts with base are suitable for immediate installation on the tank frame. In order to maximize the life-span of the contacts and to minimize repair and down times,...

High Current Contact Saddles 4000 – 14000 A Two Piece Model The 4000 A and up range, proven for many years. The standard version is supplied as a contact pair, i.e. delivered in two non connected halves. This allows the contacts to be set individually according to the bus-bar thickness for installation. The installation distance of the contact halves must be less than the thickness of the bus-bar (depending on the contact block or weight of the bus-bar 4 – 6 mm; consultation required). Inserting the busbar works with the bar’s own weight which makes these contacts very efficient for fully automatic...

High Current Contact Saddles 4000-14000 A Two Piece Model Part No. Part No. Part No. Contact block Contact block 1 set Replacement complete with base contact elements Prefabricated 20011 20022 20033 20044 20055 20066 20077 17231 17241 17251 17261 17271 17281 17291 17371 17381 17391 17401 17411 17421 17431 max. load 4000 6000 7000 8000 10000 12000 14000 Accessories/Replacements 30702 1 Piece installed mounting guide 17198 Replacement foils, Type – 2 fold 17199 Replacement foils, Type – 3 fold A A A A A A A Suitable bus-bar height mm 160 160 160 160 160 160 160 - Number of contact fingers 15 x...

High Current Contact Saddles 250 - 4000 A One Piece Model with Integrated Guides This range of contacts is a further development based on our standard version. The construction of the contact finger has been modified with an easy exchange foil package which in cases decreases the size of the unit. Furthermore, guides have been integrated directly in the main module on each side. Besides technical improvements, this also creates an overall less expensive solution as well. These contacts are delivered as a one piece model for bus-bar thickness 10, 15 or 20 mm. Although the installation size of...

High Current Bolt Contacts 1000 - 12000 A With Spring Fed Contact Bolts druseidt System druseidt High Current Bolt Contacts consist of two equal contact halves that are fixed together. These are configured for the required bus-bar thickness before delivery. For bus-bar thickness over 10 mm, respective spacing elements are utilised. The current transfer is made over several points on the spring fed E-Cu contact bolts with a beryllium disk. The amount and layout of the contact bolts depends on the desired current load and the height of the bus-bar. Inserting the bus-bar is performed using the bar’s...

Pneumatically Activated High Current Contacts 1500 - 3000 A druseidt System – Compact model 2500 This extremely robust and durable system developed by druseidt provides a loss-free current transfer to the bus-bar. With the standard version, the contactor consists of a fixed contact plate with a inflexible connection to the contact rail and a pneumatically activated moveable contact plate which is held back with a spring and requires no connection to the contact rail. The stamped contact surfaces are formed for an optimum current transfer. The pneumatic drive runs with a so-called pneumatic cushion...

Pneumatically Activated High Current Contacts 4000 - 12000 A druseidt System – Compact model 3000 Pneumatically activated high current contacts of the druseidt „Compact model 3000“ range are utilised with high current levels and heavy bus-bars (e.g. in anodising and hard chrome systems) because of their high pressure contact and the extra stable construction. The basic construction as well as the protective covers are built of stable rust-free and acid-resistant stainless steel. Current is transferred on both sides through specially stamped E-Cu contact plates. The pneumatic drive use a pneumatic...