Master Catalog
200Páginas

CATALOG CV9 Cylinders , Valves , & Accessories

QUICK INDEX Pancake® Cylinders Longstroke™ Cylinders are registered trademarks of FABCO-AIR INC. Delrin® is a registered trademark of DuPont Corp. Duralon® is a registered trademark of Rexnord Corp. Loctite® is a registered trademark of Loctite Corp. Magnalube®-G is a registered trademark of Carleton Stuart Corp. Poly Pak® is a registered trademark of Parker Hannifin Corp. Teflon® is a registered trademark of DuPont Corp. Viton® is a registered trademark of DuPont Corp. Multi-Powei® Cylinders Multi-Powei® Boosters Piston Position Sensors - now included within each cylinder section Air-Oil...

Consider asking Fabco-Air for a modified or special product to meet your necessary and specific re- quirements. Fabco-Air has the willingness, years of experience, manpower and equipment available to design, adapt, modify and produce in any quantity, existing or new products to meet your job require- ments more effectively. Please contact your local distributor with details of your requirements so that The photos here show just a few examples of the thousands of specials that have been produced over the past three decades. ■ Rear tapped mount with extension hub ■ Manifolded inlet into both...

Modular Valve Bank ■ Stacked with mounting brackets ■ Swivel flow controls ■ Fittings ■ Wire terminals ■ Wire insulation installed ■ Double rod ■ oversized rods ■ Oversized hole through ■ Double rods with hole through concentric shafts and independent ports for stripper control ■ 2 stage Multi-Power® principle Longstroke® Pivot Mount ■ 2 stage Multi-Power® principle

Pancake» Cylinders Section 11ndex Detailed Specification Model Number Codes Standard Dimensions Seal Kit Part Numbers Magnetic Piston Position Sensing Option Dimensions Flow Controls Specifications subject to change without notice or incurring obligation

Features & Benefits This, the original Pancake® Cylinder, was designed in 1958 to satisfy the need for short stroke cylinders that would fit in very tight spaces. Today, with almost four decades of experience in thousands of cylinder applications around the world, The Pancake® Line offers you far more than any of its imitators - more features and options - better quality, strength and appearance - and far longer product life! We are so confident in our design and manufacturing skills that we back every Pancake® Cylinder with our 2-year Warranty! Laboratory tests confirm that internally...

Pancake® Cylinders °8i9B^ês&ï72 S-e4ifS Construction Details Nearly 4 decades of experience paying close attention to design detail, production and assembly techniques have resulted in the ultimate Fabco-Air Pancake0, short stroke cylinders. Pancakes0 fit into very tight spaces and virtually ANY short stroke cylinder application. Think how well they will fit with your application! 1. The heavy wall prohibits any damage to the bore from external 2. The one piece cylinder body and bushing support end is machined from solid aluminum bar-stock. This provides unequalled strength, rigidity, and...

Action Information PTFE Piston Bearing Action Letter Action Description Double Acting Power Extend - Power Retract Double Acting Power Extend - Power Retract Piston guide pins for nonrotating Single Acting - Spring Retracted Power Extend - Spring Retract Single Acting - Spring Extended Spring Extend - Power Retract Specifications subject to change without notice or incurring obligation

Pancake® Cylinders 0Q%1%S^-Ps Action Information The "Action Letter" portion of the Pancake® Model Number specifies how many piston rods the cylinder has (Single Rod or Double Rod), how the piston rod is extended and retracted (Double Acting or Single Acting), and if the piston rod is restricted from rotating by internal guide pins (Nonrotating). Original Series PTFE Piston Bearing 11 Symbol Action Letter Action Description Double Acting Two Piston Rods - One each end Power Extend - Power Retract Action -XDRK Double Acting Two Piston Rods - One each end Power Extend - Power Retract Piston...

Option Information PREFIX OPTIONS MODEL NUMBER PREFIX METRIC Cylinder and Rod Thread. M Female Rod Thread is standard. Optional Male Rod Thread PREFIX OPTIONS Mounting holes and rod thread are configured to common METRIC sizes. Ports in 1/2" (5) and 3/4" (7) bores are M5. Ports in 1-1/8" (121) bore and larger are G1/8 with 14mm spotface for 1/8 BSP-Parallel Available on all series, bore, stroke and action combinations. See Option Specifications pages of desired bore and action for complete dimensional details. Specifications subject to change without notice or incurring obligation

Pancake® Cylinders Option Information SUFFIX OPTIONS MODEL NUMBER SUFFIX Double Rod, Both Ends SUFFIX OPTIONS A high strength stud is threaded into the standard female rod end and retained with Loctite®. This method eliminates the small diameter thread relief area normally required when machining male threads. This provides a much stronger rod end which can be repaired, rather than replacing the complete rod, should the thread be damaged. Available on all series, bore, stroke and action combinations. See Option Specifications pages of desired bore and action for complete dimensional...

Pancake® Cylinders Construction Details SUFFIX OPTIONS MODEL NUMBER SUFFIX HYDRAULIC, Low Pressure Service Consult factory for media compatability and operating temperatures over 300°F. With Standard Thickness With Thick Cover SUFFIX OPTIONS For Air-Oil or Hydraulic systems to 500 psi NONSHOCK. 1. A specially formulated U-Cup seal replaces the O-ring piston rod seal. This eliminates leakage past the rod seal and around the bushing. 2. Option -HHC, on single rod bores 1 -5/8" (221 ) & larger, includes a thicker rear cover to assure that there is no warpage or failure when the mounting...

Pancake® Cylinders Option Information SUFFIX OPTIONS HOLE THRU Double Rod Shaft SUFFIX OPTIONS 150 psi maximum operating pressure A hole is drilled through the piston rods & the double rod stud (see construction details on page 1.3). This hole is used for the passage of Vac- uum, Air, Gas, Oil, Liquid or any media that is compatible with the stainless steel piston rod and the steel stud. Maximum pressure, 150 psi. Hole sizes available for each bore size are shown in the chart to the left. If a larger hole is needed (for higher flows or mechanical members) or all stainless steel construction...